ELASTIFLASH
USES OUTSTANDING FEATURES
ELASTIFLASH has excellent adhesion quality
Forms a strong and durable bond.
Has excellent expansion and contraction properties, similar
to rubber and can withstand the extreme expansion and
contraction of the high stress areas of the roof such as
flashing and/or joints, even at extremely low temperatures.
Fortified to withstand heat and ultra violet radiation.
Durable and easy to apply.
Single component. Can be applied straight from the
container, thereby saving labour costs.
ELASTIFLASH is a universal compound ideal for roof flashing, details,
patching of cracks and splits in roofs, repair of flashing details, roof
blisters, roof curbs, vent pipes, skylights, spouts, wall and foundation.
It is also suitable to seal cracks in concrete walls and floors as well as
tile joints.
ELASTIFLASH is recommended when extreme expansion and contraction can
occur and when elastic properties are desirable.
DESCRIPTION
BITUMAT
ELASTIFLASH is a high quality, trowel grade, cold applied, rubberized
bitumen cement formulated with ductile bitumen, rubber, mineral
stabilizers and special anti oxidation/ozone additives.
INSTALLATION
APPLICATION CLEANING COVERAGE RATES : STANDARDS PACKING HEALTH & SAFETY
The
surface must be clean, free of dirt, dust and debris, grease or oil. Over
concrete, metal or brittle asphalt surfaces, prime with BITUFAST before
applying ELASTIFLASH. It does not require any heating or thinning. It can
be applied by trowel or putty knife.
Tools : Clean with kerosene
Hands : Use a hand cleaner or kerosene, followed by soap and water.
One course application: 2.4 - 2.5 Kg/M2 Two course application: 4.8 -
5.0 Kg/M2 (Allow 1 st course to cure 4 hours before installing 2nd course)
Exceeds the performance requirement of ASTM D 4586
20-kg pails and 200-kg drums
Contains Petroleum distillate; flammable; keep away from open fire,
sparks or other ignition sources. Wear protective clothing, gloves and
goggles.
1 . Fire - Flammable when wet, flash point 40 deg. C.
2. Skin - Avoid repeated or prolonged contact. Remove with hand cleaner
that removes oil or grease, then clean with soap and water.
3. Eyes - Contact could cause irritation. If contact occurs flush with
clean water.
4. Inhalation - Can cause dizziness. Remove to fresh air. If breathing
difficulty persist, administer oxygen.
|
Property |
Result |
Test Method |
|
Density at 250C., Kg/Ltr. |
1.0 - 1.2 |
ASTM D 70 |
|
Consistency, Cone Penetration at 250. dmm |
230-300 depending on grade |
ASTM D-217 |
|
Dry film thickness, 1 liter/M2, mm |
0.65 |
- |
|
Drying time, to touch, 25 oCHr. |
8 (at recommended coverage) |
- |
|
Drying time, through, 25 oCHr. |
7 (-do-) |
- |
|
Colour |
Black |
- |
|
Cold temperature pliability at 0 0C |
No cracking or peeling |
ASTM D-4586 |
|
Resistance to heat at 60 0C |
No sagging or blistering |
ASTM D-4586 |
|
Adhesion to wet surface |
Excellent |
ASTM D- 3409 |
|
Adhesion to dry surfaces |
Excellent |
ASTM D 3409 |
|
Resistance
to sunlight (UV) |
Pass |
ASTM G- 53 |
|
Resistance to mild acids and alkalies |
Good |
- |
|
Resistance to water |
Excellent |
ASTM G- 53 |
|
Service temperature, 0C |
0 to 90 |
- |
|
Non Volatile, % Wt |
67-72 |
ASTM D-4586 |
|
Volatile, % Wt. |
28 - 33 |
ASTM D-4586 |
|
Bitumen content, % Wt. |
40 (min) |
ATM D-4 |
|
Mineral stabilizers and fibers, % Wt. |
23 - 27 |
ASTM D 4479 |