Main

PRODUCTS

PREMIERFLEX 3000

DESCRIPTION
PREMIERFLEX 3000 is an SBS modified bituminous waterproofing membrane reinforced with spun-bond polyester fabric. the combination gives the proven waterproofing qualities of bitumen combined elasticity excellent resistance to weathering and ease of application.

USES
PREMIERFLEX 3000 is a general purpose waterproofing membrane and is excellent in single layer roofing systems or as part of a multi-layer system. When surfaced with granular slates PREMIERFLEX 3000 is ideal as an exposed top layer.

OUTSTANDING FEATURES
· Excellent cold weather resistance.
· High tensile strength and tear resistance.
- Good elongation and recovery.
- Very good puncture resistance
- Rot proof.
- Highly resistant to substrate movement.

STANDARDS
PREMIERFLEX 3000 complies with the requirements and tolerance levels of :
1. The American Societty For Testing & Material ASTM D-6164 Type I > II .
2.UEAtc (European Union of Technical Agreement).
3.MOAT 27-1983 and MOAT 30-1984.
4.CGSB (Canadian General Standards Board) 37-GP56M-July 1980.

INSTALLATION TOOLS REQUIRED
Gas torch, Knife, Trowel, Measuring tape, Marking string, Gloves.

APPLICATION
PREMIERFLEX 3000 is installed by torch welding method, loose-laid or fully bonded to substrate. When loose-laid, only laps are bonded together. Peripheries and protrusions are sealed according to specifications.

COVERAGE RATE
For flat areas

1.13 M2/M2 per layer

For 30 cm. girth flashing

0.35 M2/Mt/ length

Average wastage

3 - 5%

TORCHING GUIDELINES
The underside of the membrane should be torched just enough to superficially melt the bitumen. Excessive heating may damage the reinforcement. Overlaps should be re-heated from the top and resealed with a trowel to ensure seam integrity.

For details of installation methods and flashing requirements, consult the relevant BITUMAT Design and Installation Manual.

FINISHES
PREMIERFLEX 3000 is available in two basic finishes:
- Black smooth finish with polyethylene surfaces for covered applications.
- Granule surfacing for exposed applications.

QUALITY CONTROL In addition to stringent regular tests by BITUMAT laboratory, our products are tested periodically by Bureau Veritas & SOCOTEC, Paris, France.

TECHNICAL DATA - PREMIERFLEX 3000

GENERAL DATA Roll length	10 mt.
Roll width	1 mt.
Thickness	3, 4, 5, mm
Reinforcement	nonwoven polyester fabric.

	Property	Result	Test Method
1.	Softening point ⁰C	115	ASTM D-36
2.	Penetration, @ 25⁰C, dmm	30	ASTM D-5
3.	Low temperature flexibility, ⁰C	-15 to -18	ASTM D-5147
4.	Heat resistance, compound stability @ 102 ⁰C for 2 hours & 15 minutes	No flow - Pass	ASTM D-5147
5.	Tensile strength, N/5 cm @ 23 ⁰C + 2 Longitudinal Transverse	800 (16 KN/m) 600 (12 KN/m)	ASTM D-5147
6.	Tensile strength, N/5 cm @ -18 ⁰C + 2 Longitudinal Transverse	1000 (20 KN/m) 750 (15 KN/m)	ASTM D-5147
7.	Elongation % @ 23 ⁰C +2 Longitudinal Transverse	45 50	ASTM D-5147
8.	Elongation % @ -18 ⁰C +2 Longitudinal Transverse	25 25	ASTM D-5147
9.	Load strain prodcut @ 23 ⁰C +2 Longitudinal Transverse	36,000 27,000	CGSB-37-GP-56M
10.	Lap joint strength N/5cm Longitudinal Transverse	800 600	CGSB-37-GP-56M UEAtc
11.	Tear resistance, N Longitudinal Transverse	400 400	ASTM D-5147
12.	Puncture Resistance, N Static indentation Dynamic indentation	950 L₃l3	ASTM E 154. UEAtc 5.1.9 UEAtc 5.1.10
13.	Water Absorption, % Wt @ 23 ⁰C 24 hrs	<0.35	ASTM D-5147
14.	Water Vapour Transmission, g/m²/24 hrs	<0.30	ASTM E-96 procedure E 37.8 ⁰C at 96% RH
15.	Diminsional Stability % Longitudinal Transverse	+ 0.5 + 0.5	ASTM D-5147
16.	Resistance To Leakage At Joints	Pass	UEAtc
17.	Resistance To Aging & U.V	No change greater than 20% of the original values	ASTM G53 UNI 8202

The data listed above is subject to the tolerance limits of UEAtc specifications

The information given in this Technical Sheet is to the best of our knowledge based on laboratory tests and practical experience. However, as the product is often used under conditions beyond our control, we cannot guarantee but the product itself.